# Arcam SA30 remains in standby and is non-responsive
**URL:** https://arcam.discourse.group/t/arcam-sa30-remains-in-standby-and-is-non-responsive/529
**Category:** Issues
**Created:** [June 12, 2021, 7:34pm UTC](https://arcam.discourse.group/t/arcam-sa30-remains-in-standby-and-is-non-responsive/529 "2021-06-12T19:34:12Z")
**Posts on this page:** 4
**Page:** 1
### Author:  [@sander](https://arcam.discourse.group/u/sander)
#### Post date: [June 12, 2021, 7:34pm UTC](https://arcam.discourse.group/t/arcam-sa30-remains-in-standby-and-is-non-responsive/529/1 "2021-06-12T19:34:12Z")
**Scenario**
Perform the following steps:
1. switch on Arcam SA30 version , build ? is used
2. start Arcam Music Life iOS app, build 2.3.6 (895) is used
3. Cold power on of device does not startup the SA30. Actually it goes into standby mode meaning the display will not lit up and the led next to the power button is red. The display remains complete blank after power on. The device cannot be managed by remote control (even with new batteries) or by music life and Arcam app or by web browser. The LAN connection is not active meaning no lights are lit up on the SA30 and on the network switch. A new ethernet cable did not solve this problem.
**Actual result**
_A non-responsive SA30_
**Expected result**
_Normal operation_
**Additional information**
A couple of weeks ago I upgraded to the latest version via the web browser. I assume this is version V1027 V1.62. This upgrade went without issues and I used the SA30 for a week of 2 without problems. I changed nothing, not in setup nor in configuration.
I usually don’t put the SA30 in standby but perform a full power off with the power button. I use the SA30 not regularly, only maybe twice a week and in total for no more than a few hours. I bought the SA30 last december.
---
### Author:  [@paulguk](https://arcam.discourse.group/u/paulguk)
#### Post date: [June 13, 2021, 11:03am UTC](https://arcam.discourse.group/t/arcam-sa30-remains-in-standby-and-is-non-responsive/529/2 "2021-06-13T11:03:08Z")
It might be worth trying a factory reset as detailed in this link.
> [@How to do a full reset and reload of firmware](https://arcam.discourse.group/t/how-to-do-a-full-reset-and-reload-of-firmware/293):
>
> I have been in email contact with one of Arcam’s field engineers about an issue I have with DIRAC. Within these email conversations I mentioned how I was always reluctant to upgrade or download firmware more than necessary due to my fear of a power outage or something else going wrong and ‘bricking’ the amp (I lost a PC motherboard years ago doing a BIOS update). He gave me some instructions on how to perform a full reset and then re load the firmware. ‘If the installation is interrupted, it s…
If that fails then you may have a faulty amp.
---
### Author:  [@sander](https://arcam.discourse.group/u/sander)
#### Post date: [June 13, 2021, 6:57pm UTC](https://arcam.discourse.group/t/arcam-sa30-remains-in-standby-and-is-non-responsive/529/3 "2021-06-13T18:57:08Z")
Thanks for the suggestion, however unfortunately it was not successful. The device did not respond to the procedure. I used a freshly formatted (FAT-32) USB memory stick with only the SWU file and pressed the service button on the back for about 1 minute. The display remained blank. I also did notice that the lights of the USB stick did not fire up (just as the LAN socket lights), so I assume it is a power problem somewhere in the device. Looks like I need to bring it in for repair. A real bummer because the device is only 6 months old and service might take some time including shipment.
---
### Author:  [@cornchip](https://arcam.discourse.group/u/cornchip)
#### Post date: [February 10, 2025, 4:53am UTC](https://arcam.discourse.group/t/arcam-sa30-remains-in-standby-and-is-non-responsive/529/5 "2025-02-10T04:53:30Z")
I had same issue as you yesterday. I did many things like f/w recovery, factory reset … refered on thr web. But, anythings are not worked 😕
I would like to know how did you fix your problem if you don’t mind.
Actually I bought it just a week ago from Japan via direct purchase. So, It is really difficult to get official service now…